Share your business, logo, and content. We’ll confirm the scope and deposit, prepare your design, and work with you through launch.

Lake Mary, FL · Epoxy & polyaspartic floors
Garage, showroom and home gym floors, prepared and coated by one crew. Pick a finish, see a sample estimate, then book a site visit.
Four systems we install most. Choose one, set your square footage, and get a sample estimate before we ever visit.

Metallic finish selected. Sample price 12 to 15 dollars per square foot.
03 Sample estimate
Your sample price includes
Not included: moisture mitigation systems or removing old coatings. Quoted after the site visit if needed.
Sample math, shown for design: square footage times a sample price range. Your exact quote follows a site visit.
Sample pricing, shown for design. Prices are installed per square foot and vary with the condition of your concrete and the size of the job.
Drag, or use the arrow keys
A · As foundB · As finishedCracked, oil-stained bare concrete garage floor beside dark cabinets and an open door (synthetic image) The same garage after grinding and coating, with a glossy graphite flake floor (synthetic image)A · As foundCracked, oil-stained concrete, tire tracks and all.
B · As finishedGround, repaired and coated: a graphite flake system under a clear topcoat. Same garage, same light.
Three kinds of space, one process: grind, repair, coat and seal.
01
Flake, metallic or solid, built for hot tires, oil and spills.
Sample from $8 / sq ft
02
Easy-to-clean floors for showrooms and offices, timed to keep downtime short.
Sample from $6 / sq ft
03
Tough, low-maintenance floors that stand up to weights, mats and daily traffic.
Sample from $8 / sq ft
Sample services, shown for design. Your own scope and policies replace them.
A floor is not a coat of paint. It is a stack, and every layer has one job. Select a layer to see what it does.
Schematic, thickness not to scale.
The clear shield. It seals the layers below against tire marks, chemicals and sun, and it is the surface you clean every day. Polyaspartic cures fast and resists UV and yellowing.
The finish you chose. Flake or quartz is broadcast into the wet body coat; metallic pigments are poured and worked by hand. This layer sets the color, pattern and grip.
The thick, tough layer. Pigmented epoxy builds thickness and color, fills the profile of the slab and carries the decorative layer on top.
The bond. It soaks into the opened pores of the ground concrete, locks down dust and gives the body coat something to grip. A moisture-tolerant formula handles the normal vapor that comes through most slabs.
The foundation, and where most coating failures start. We diamond-grind the slab to a clean, even profile, cut and fill cracks and joints, and test moisture before any resin goes down.
Not sure what your floor needs?We test the slab at the site visit and write the system for your space into your quote.
Typical values for a residential system, shown for design. One mil is a thousandth of an inch. Products and cure times vary by job; your written quote lists yours.
Four sample floors from Surface Studio. Open one to see the system behind it.

Plate 01 · Garage floors
A dark metallic floor under a classic coupe. Poured and worked by hand, so no two look alike.

Plate 02 · Garage floors
Graphite flake under a high-gloss clear coat. Built for hot tires, oil, spills and the occasional dropped wrench.

Plate 03 · Showrooms & commercial
A smooth, easy-to-clean floor for a glass-walled showroom, scheduled over a weekend to keep downtime short.

Plate 04 · Home gyms & studios
A dark flake floor that stands up to weights, mats and daily traffic, and wipes clean.
Sample projects, shown for design. Areas and timings are typical examples, not records of real jobs.
A typical install
A sample schedule for a two-car garage. Yours is confirmed at the site visit.
01 · Site visit
We measure, check moisture and look at the concrete, then confirm your quote on the spot.
02 · Prep
Walls and cabinets are masked, dust control goes up, and we walk the floor with you one last time.
02 · Prep
Diamond grinding opens the pores and evens out the slab. Dust is captured at the machine.
02 · Prep
Cracks and joints are cut, filled and flattened. Moisture is checked again.
03 · Coat
A moisture-tolerant primer goes down and soaks into the ground concrete.
03 · Coat
Pigmented epoxy is poured, squeegeed and back-rolled. Flake goes in while it is wet, or metallic pigments are worked by hand.
03 · Coat
Loose flake is scraped and swept away, leaving a clean, even surface.
03 · Coat
A clear polyaspartic topcoat seals every layer underneath.
04 · Cure & handover
Light foot traffic the next day, vehicles in about three days. You get care instructions in writing.
Mechanical prep for a bond that lasts.
Joints and spalls fixed before any coating.
A clear topcoat against tires, chemicals and sun.
Note 01 · Garage floor, flake finish
They ground the floor, fixed the cracks I had ignored for years, and the finish looks like a showroom. The crew left the garage cleaner than they found it.
Greg H.
Note 02 · Showroom floor
We needed the shop floor done over a weekend. They kept to the schedule, and the floor is easy to mop clean.
Tasha M.
Note 03 · Metallic garage floor
The metallic finish is the first thing everybody mentions. Clear communication from quote to handover.
Owen B.
Sample reviews. Your real client reviews go here.
Straight answers about prep, cure times, moisture and what to expect from your floor.
With proper prep and a quality topcoat, residential floors commonly last for many years. Sunlight, heavy use and moisture all affect lifespan, so we explain what to expect for your space.
Yes. We repair cracks and joints, and grind out surface contamination. Heavy oil saturation needs a closer look, which we do at the site visit.
A moisture-tolerant primer handles the normal vapor that comes through most slabs. We test the concrete at the site visit, and if readings run high we tell you before quoting and explain the fix rather than coat over a problem.
Walk on it lightly the next day and drive on it in about three days. We give you a precise timeline with your quote.
Epoxy builds thickness and color. Polyaspartic topcoats cure faster and resist UV and yellowing. Most of our systems use both.
We add a fine non-slip texture where you need it, such as entries and near drains. Tell us about the space and we will suggest the right profile.
Coatings give off a strong smell while they cure, so we run fans and keep the space ventilated. Keep pets and kids out of the room while the smell is strong, and off the new floor until it is walkable, usually the next day. We confirm the exact timing at the site visit.
Clear the floor edge to edge: shelves, bikes, tool chests and anything stored along the walls. Plan to park outside or in the driveway until the floor can take vehicles, usually about three days. We send a short checklist with your quote so nothing gets missed.
Most epoxy and polyaspartic systems go down best with the slab and the air roughly between 50 and 90 °F, and with no moisture condensing on the floor. Hot, humid or damp days slow the cure, so we check conditions on the morning of the install and reschedule if they are off.
The floor is the first thing you see.
Send us the size and use of your space. We confirm a time to measure and check the concrete, then follow with a written quote.
Sample terms. A free on-site measure and quote is shown for design. Your written quote lists the terms that apply.